FREE AUDIO REMASTERING. SEND US YOUR SONG AND WE WILL RE-MASTER IT AND SEND YOU AN MP3 OF THE RESULTS FREE. TRITIUM ELECTRONICS SUPERB HIGH END TURNTABLES, INTERCONNECTS, TRIPHAZERS SEE WWW.BEERCITYAUDIO.COM FOR DETAILS www.mediafire.com COOL SONGS WATCH IT TO THE RUN OUT GROOVE.. WWW.BEERCITYAUDIO.COM TRITIUM AIR BEARING ULTIMATE VISCOUS DAMPED TONEARM & TURNTABLE. Viscous damped in the vertical as well as horizontal plane. Damping takes place at the headshell for maximum control. Undamped tonearms have a very colored presentation from vibrations set up by the needle. Their sound is far from what is possible from the Vinyl LP format. Undamped or rear damped tonearms are not even close in terms of fidelity, tracking and Vinyl wear. The Tritium Tonearm is a perfected design for Medium to High compliance cartridges and gives about a 10 to 12 hertz tonearm resonance frequency. Tonearm weighs about 34 Grams with this 8 gram cartridge and has a 10 hertz arm resonance frequency. We have one MC cartridge with over 4000 playing hours on it and a Shelter with 2800 hours! And no visible wear under a 700 power Stereo microscope AMAZING… ! Lowest Mass, Lowest Wear, Highest trackability, Highest compliance tonearm in the world. ( OTF VTA ) ON THE FLY Vertical Tracking Alignment adjustment is a screw on top of the Tonearm pivot. -COMPLETELY FRICTIONLESS for the MOST ACCURATE LP PLAYBACK EVER- NO pivoted or linear arm design available can compare! 33 RPM, 45 RPM and Optional 78 RPM …
The dolly has two sets of locating holes for the tripod legs, which means the tripod can be used in both high and low positions. It has eight radial ball bearing wheels which set the track width to the correct positions as the dolly moves down the track. The Tracking Dolly is ideal for use on location or in the studio, all you need is a reasonably flat surface. The dollies width has been set to allow it to go through doorways, it has its own levelling system which prevents any rocking should the track be on uneven ground. It runs on inexpensive 40mm dia. PVC pipe which can be supplied or is available from DIY stores. The dolly will accept all tripods that have feet smaller than 45mm in diameter or with a base spreader, 3 straps are supplied for securing your tripod to the dolly and also supplied are 2 track connectors for joining your track.
Nice Ball Bearing N6908BTN Double Sealed, Extended Inner Ring, 52100 Bearing Quality Steel, 0.5000″ Bore x 1.6250″ OD x 1.0000″ Width
Nice Ball Bearing N6908BTN Double Sealed, Extended Inner Ring, 52100 Bearing Quality Steel, 0.5000″ Bore x 1.6250″ OD x 1.0000″ Width Feature
This bearing is not flanged and can be assembled directily in a housing
Pregreased with metered Shell Alvania #2 grease
Suitable for medium loads and moderate speeds
Extended inner ring with 2 set screws for securing a shaft
Although not the self-aligning type, this bearing will accommodate a limited amount of angular misalignment “Capitalization”
Nice Ball Bearing N6908BTN Double Sealed, Extended Inner Ring, 52100 Bearing Quality Steel, 0.5000″ Bore x 1.6250″ OD x 1.0000″ Width Overview
The 6900 Series consists of a double sealed, semi-ground bearing with an extended inner ring. It is provided with two set screws. RBC Nice Bearings is a subsidiary of RBC Bearings. RBC Bearings has been providing bearing solutions to our customers since 1919. A publicly-traded company (NASDAQ: ROLL), RBC currently has 23 manufacturing facilities worldwide, with 18 located in the USA.
Nice Ball Bearing N6908BTN Double Sealed, Extended Inner Ring, 52100 Bearing Quality Steel, 0.5000″ Bore x 1.6250″ OD x 1.0000″ Width Specifications
R4ZZ Bearing 1/4 x 5/8 x 0.196 Shielded Inch Feature
Item: Double Shielded Ball Bearings
“Size: 1/4″” x 5/8″” x 0.1960″”"
“Size: 0.2500″” x 0.6250″” x 0.1960″”"
Size: 6.350mm x 15.875mm x 4.978mm
Type: Deep groove ball bearings
R4ZZ Bearing 1/4 x 5/8 x 0.196 Shielded Inch Overview
“Ball Bearings R4 ZZ 1/4″” x 5/8″” x 0.1960″” R4ZZ Ball Bearing, the inner diameter is 1/4″”, outer diameter is 5/8″” and the width is 3.14/16″”, this is a popular size that could be used in many applications, each bearing has 2 metal shields to protect the bearing from dust or any possible contamination, also bearings are pre-lubricated with grease. * Item: Double Shielded Ball Bearings * Size: 1/4″” x 5/8″” x 0.1960″” * Size: 0.2500″” x 0.6250″” x 0.1960″” * Size: 6.350mm x 15.875mm x 4.978mm * Type: Deep groove ball bearings * Closures: Metal Shields * Lubrication: Self Lubricated (Grease) * Quantity: One Bearing”
R4ZZ Bearing 1/4 x 5/8 x 0.196 Shielded Inch Specifications
admin